Specifies an address to listen on for a stream ( SOCK_STREAM ), datagram ( SOCK_DGRAM ), or sequential packet ( SOCK_SEQPACKET ) socket, respectively. The address can be written in various formats:

If the address starts with a slash ( / ), it is read as file system socket in the AF_UNIX socket family.

If the address starts with an at symbol ( @ ), it is read as abstract namespace socket in the AF_UNIX family. The @ is replaced with a NUL character before binding. For details, see unix(7) .

If the address string is a single number, it is read as port number to listen on via IPv6. Depending on the value of BindIPv6Only= (see below) this might result in the service being available via both IPv6 and IPv4 (default) or just via IPv6.

If the address string is a string in the format v.w.x.y:z, it is read as IPv4 specifier for listening on an address v.w.x.y on a port z.

If the address string is a string in the format [x]:y, it is read as IPv6 address x on a port y. Note that this might make the service available via IPv4, too, depending on the BindIPv6Only= setting (see below).

Note that SOCK_SEQPACKET (i.e. ListenSequentialPacket= ) is only available for AF_UNIX sockets. SOCK_STREAM (i.e. ListenStream= ) when used for IP sockets refers to TCP sockets, SOCK_DGRAM (i.e. ListenDatagram= ) to UDP.

These options may be specified more than once in which case incoming traffic on any of the sockets will trigger service activation, and all listed sockets will be passed to the service, regardless of whether there is incoming traffic on them or not. If the empty string is assigned to any of these options, the list of addresses to listen on is reset, all prior uses of any of these options will have no effect.

It is also possible to have more than one socket unit for the same service when using Service= , and the service will receive all the sockets configured in all the socket units. Sockets configured in one unit are passed in the order of configuration, but no ordering between socket units is specified.

If an IP address is used here, it is often desirable to listen on it before the interface it is configured on is up and running, and even regardless of whether it will be up and running at any point. To deal with this, it is recommended to set the FreeBind= option described below.

Specifies a file system FIFO to listen on. This expects an absolute file system path as argument. Behavior otherwise is very similar to the ListenDatagram= directive above.

Specifies a special file in the file system to listen on. This expects an absolute file system path as argument. Behavior otherwise is very similar to the ListenFIFO= directive above. Use this to open character device nodes as well as special files in /proc and /sys .

Specifies a Netlink family to create a socket for to listen on. This expects a short string referring to the AF_NETLINK family name (such as audit or kobject-uevent ) as argument, optionally suffixed by a whitespace followed by a multicast group integer. Behavior otherwise is very similar to the ListenDatagram= directive above.

Specifies a POSIX message queue name to listen on. This expects a valid message queue name (i.e. beginning with /). Behavior otherwise is very similar to the ListenFIFO= directive above. On Linux message queue descriptors are actually file descriptors and can be inherited between processes.

Takes a one of default , both or ipv6-only . Controls the IPV6_V6ONLY socket option (see ipv6(7) for details). If both , IPv6 sockets bound will be accessible via both IPv4 and IPv6. If ipv6-only , they will be accessible via IPv6 only. If default (which is the default, surprise!), the system wide default setting is used, as controlled by /proc/sys/net/ipv6/bindv6only , which in turn defaults to the equivalent of both .

Takes an unsigned integer argument. Specifies the number of connections to queue that have not been accepted yet. This setting matters only for stream and sequential packet sockets. See listen(2) for details. Defaults to SOMAXCONN (128).

Specifies a network interface name to bind this socket to. If set, traffic will only be accepted from the specified network interfaces. This controls the SO_BINDTODEVICE socket option (see socket(7) for details). If this option is used, an automatic dependency from this socket unit on the network interface device unit ( unitfile_device(5) is created.

Takes a UNIX user/group name. When specified all AF_UNIX sockets and FIFO nodes in the file system are owned by the specified user and group. If unset (the default), the nodes are owned by the root user/group (if run in system context) or the invoking user/group (if run in user context). If only a user is specified but no group, then the group is derived from the user's default group.

If listening on a file system socket or FIFO, this option specifies the file system access mode used when creating the file node. Takes an access mode in octal notation. Defaults to 0666.

If listening on a file system socket or FIFO, the parent directories are automatically created if needed. This option specifies the file system access mode used when creating these directories. Takes an access mode in octal notation. Defaults to 0755.

Takes a boolean argument. If true, a service instance is spawned for each incoming connection and only the connection socket is passed to it. If false, all listening sockets themselves are passed to the started service unit, and only one service unit is spawned for all connections (also see above). This value is ignored for datagram sockets and FIFOs where a single service unit unconditionally handles all incoming traffic. Defaults to false . For performance reasons, it is recommended to write new daemons only in a way that is suitable for Accept=false . A daemon listening on an AF_UNIX socket may, but does not need to, call close(2) on the received socket before exiting. However, it must not unlink the socket from a file system. It should not invoke shutdown(2) on sockets it got with Accept=false , but it may do so for sockets it got with Accept=true set. Setting Accept=true is mostly useful to allow daemons designed for usage with inetd(8) to work unmodified with systemd socket activation.

The maximum number of connections to simultaneously run services instances for, when Accept=true is set. If more concurrent connections are coming in, they will be refused until at least one existing connection is terminated. This setting has no effect on sockets configured with Accept=false or datagram sockets. Defaults to 64.

Takes a boolean argument. If true, the TCP/IP stack will send a keep alive message after 2h (depending on the configuration of /proc/sys/net/ipv4/tcp_keepalive_time ) for all TCP streams accepted on this socket. This controls the SO_KEEPALIVE socket option (see socket(7) and the TCP Keepalive HOWTO for details.) Defaults to false .

Takes an integer argument controlling the priority for all traffic sent from this socket. This controls the SO_PRIORITY socket option (see socket(7) for details.).

Takes an integer argument controlling the receive or send buffer sizes of this socket, respectively. This controls the SO_RCVBUF and SO_SNDBUF socket options (see socket(7) for details.).

Takes an integer argument controlling the IP Type-Of-Service field for packets generated from this socket. This controls the IP_TOS socket option (see ip(7) for details.). Either a numeric string or one of low-delay , throughput , reliability or low-cost may be specified.

Takes an integer argument controlling the IPv4 Time-To-Live/IPv6 Hop-Count field for packets generated from this socket. This sets the IP_TTL/IPV6_UNICAST_HOPS socket options (see ip(7) and ipv6(7) for details.)

Takes an integer value. Controls the firewall mark of packets generated by this socket. This can be used in the firewall logic to filter packets from this socket. This sets the SO_MARK socket option. See iptables(8) for details.

Takes a boolean value. If true, allows multiple bind(2) s to this TCP or UDP port. This controls the SO_REUSEPORT socket option. See socket(7) for details.

Takes a string value. Controls the extended attributes security.SMACK64 , security.SMACK64IPIN and security.SMACK64IPOUT , respectively, i.e. the security label of the FIFO, or the security label for the incoming or outgoing connections of the socket, respectively. See Smack.txt for details.

Takes an integer value. Controls the pipe buffer size of FIFOs configured in this socket unit. See fcntl(2) for details.

These two settings take integer values and control the mq_maxmsg field or the mq_msgsize field, respectively, when creating the message queue. Note that either none or both of these variables need to be set. See mq_setattr(3) for details.

Takes a boolean value. Controls whether the socket can be bound to non-local IP addresses. This is useful to configure sockets listening on specific IP addresses before those IP addresses are successfully configured on a network interface. This sets the IP_FREEBIND socket option. For robustness reasons it is recommended to use this option whenever you bind a socket to a specific IP address. Defaults to false .

Takes a boolean value. Controls the IP_TRANSPARENT socket option. Defaults to false .

Takes a boolean value. This controls the SO_BROADCAST socket option, which allows broadcast datagrams to be sent from this socket. Defaults to false .

Takes a boolean value. This controls the SO_PASSCRED socket option, which allows AF_UNIX sockets to receive the credentials of the sending process in an ancillary message. Defaults to false .

Takes a boolean value. This controls the SO_PASSSEC socket option, which allows AF_UNIX sockets to receive the security context of the sending process in an ancillary message. Defaults to false .

Takes a string value. Controls the TCP congestion algorithm used by this socket. Should be one of "westwood", "veno", "cubic", "lp" or any other available algorithm supported by the IP stack. This setting applies only to stream sockets.

Takes one or more command lines, which are executed before or after the listening sockets/FIFOs are created and bound, respectively. The first token of the command line must be an absolute filename, then followed by arguments for the process. Multiple command lines may be specified following the same scheme as used for ExecStartPre= of service unit files.

Additional commands that are executed before or after the listening sockets/FIFOs are closed and removed, respectively. Multiple command lines may be specified following the same scheme as used for ExecStartPre= of service unit files.

Configures the time to wait for the commands specified in ExecStartPre= , ExecStartPost= , ExecStopPre= and ExecStopPost= to finish. If a command does not exit within the configured time, the socket will be considered failed and be shut down again. All commands still running will be terminated forcibly via SIGTERM , and after another delay of this time with SIGKILL . (See KillMode= in unitfile_kill(5) .) Takes a unit-less value in seconds, or a time span value such as "5min 20s". Pass 0 to disable the timeout logic. Defaults to DefaultTimeoutStartSec= from the manager configuration file (see systemd-systemd.conf(5) ).

Specifies the service unit name to activate on incoming traffic. This setting is only allowed for sockets with Accept=no . It defaults to the service that bears the same name as the socket (with the suffix replaced). In most cases, it should not be necessary to use this option.